instantreality 1.0

• Node 12
• SceneBaseNode 17
• UnboundedNode 8
• VisualProperty 9
• ShapeProperty 2
• Geometry 2
• ViewIndependentGeometry 2
• DynamicGeometry 2
• ParametricGeometry 5
• NurbsSurface 2
• NurbsTrimmedSurface

XML encoding

<NurbsTrimmedSurface uTessellation='1'
vTessellation='1'
weight=''
solid='TRUE'
ccw='TRUE'
uClosed='FALSE'
uDimension='0'
uKnot=''
uOrder='3'
vClosed='FALSE'
vDimension='0'
vKnot=''
vOrder='3'
meshGenerationType='auto'
lit='TRUE'
resolution='1'
multiResolutionLevel='1'
invalidateVolume='FALSE'
normalUpdateMode='nice'
cacheMode='auto'
optimizationMode='auto'
logFeature=''
 />

Classic encoding

NurbsTrimmedSurface {
	uTessellation 1
	vTessellation 1
	weight []
	solid TRUE
	ccw TRUE
	uClosed FALSE
	uDimension 0
	uKnot []
	uOrder 3
	vClosed FALSE
	vDimension 0
	vKnot []
	vOrder 3
	meshGenerationType "auto"
	lit TRUE
	resolution 1
	multiResolutionLevel 1
	invalidateVolume FALSE
	normalUpdateMode "nice"
	cacheMode "auto"
	optimizationMode ["auto"]
	logFeature [""]
}

Filter: X3D only | Avalon only | All

id	Name	DataType	PartType	Default	ValueType	Description
	uKnot	MFDouble	initializeOnly			Knot vector, where size = number of control points + order of curve.
	vKnot	MFDouble	initializeOnly			Knot vector, where size = number of control points + order of curve.
	weight	MFDouble	inputOutput			Vector assigning weight to each control point.
	trimmingContour	MFNode	inputOutput		Contour2D	The trimmingContour field, if specified, shall contain a set of Contour2D nodes.
	logFeature	MFString	inputOutput		state, child, parent, route, eventIn, eventOut	controls the logging of changes, state: log state changes (e.g. live), child: log child add/remove, parent: log parent add/remove, route: log route add/remove; eventIn: log receiving of events, eventOut: log sending of events: guiView, runtime system should create node-view, guiEdit: runtime system should create node-editeverything: log everything
	optimizationMode	MFString	inputOutput	auto	auto; all, none, sharedVertex; stripFan; vertexResort; reduceIndexSize; singleIndex	optimization mode settings; used leading +/- to switch modes on and off
	ccw	SFBool	initializeOnly	TRUE		If ccw is TRUE, the normals shall follow the right hand rule. Also used for orientation of trajectory curve.
	invalidateVolume	SFBool	inputOutput	FALSE		set volume invalid
	lit	SFBool	initializeOnly	TRUE		Specifies whether to enable/disable lighting the geometry. TRUE enables lighting, FALSE disables lighting.
	solid	SFBool	initializeOnly	TRUE		Setting solid true means draw only one side of polygons (backface culling on), setting solid false means draw both sides of polygons (backface culling off). Warning: default value true can completely hide geometry if viewed from wrong side!
	uClosed	SFBool	initializeOnly	FALSE		Whether opposite surface sides are closed (seamless) across u dimension.
	vClosed	SFBool	initializeOnly	FALSE		Whether opposite surface sides are closed (seamless) across u dimension.
	resolution	SFFloat	inputOutput	1		factor for subdivision of mesh
	multiResolutionLevel	SFInt32	initializeOnly	1		resolution level in progressive mesh
	uDimension	SFInt32	initializeOnly	0		Number of control points in u dimension.
	uOrder	SFInt32	inputOutput	3		Define order of surface by polynomials of degree = order-1.
	uTessellation	SFInt32	inputOutput	1		hint for surface tesselation.
	vDimension	SFInt32	initializeOnly	0		Number of control points in v dimension.
	vOrder	SFInt32	initializeOnly	3		Define order of surface by polynomials of degree = order-1.
	vTessellation	SFInt32	inputOutput	1		hint for surface tesselation.
	addTrimmingContour	SFNode	inputOnly		Contour2D	add Trimming Contour field
	controlPoint	SFNode	inputOutput		Coordinate	controlPoint defines a set of control points of dimension uDimension x vDimension. This set of points defines a mesh where the points do not have a uniform spacing.
	metadata	SFNode	inputOutput		MetadataObject	container for payload metadata inside MetadataSet element
	removeTrimmingContour	SFNode	inputOnly		Contour2D	remove Trimming Contour field
	texCoord	SFNode	inputOutput		VisualProperty	texCoord provides additional information on how to generate texture coordinates. By default, texture coordinates are generated automatically from the parametric subdivision.
	cacheMode	SFString	initializeOnly	auto	auto; dlist; vbo; off	controls the creation of geo cache objects; auto is vbo or dlist for dynamic objects
	meshGenerationType	SFString	inputOutput	auto	auto; dynamic; simpleStatic; advancedStatic	Geometry creation mode. Note: 'simpleStatic' needs 'glu 1.3' and may not work correctly under Windows.
	normalUpdateMode	SFString	initializeOnly	nice	none; fast; nice	force update of normals; nice update is with creaseAngle, fast is without